Generator Excitation system

Excitation system:- Turbo Generators can be supplied with any of the following conventional excitation systems as per customer requirements. Conventional excitation system. Static excitation system. Brushless excitation system. Protection system. a) Conventional excitation system:- The system consists of D.C exciter directly connected to the generator field the field of the exciter is controlled by an […]

Continue Reading

Generator Lubrication system

Lubrication system:- The bearing lubrication is done by circulating oil under pressure and the complete system forms part of the main tube of the system of the turbine. Slip rings:- Slip rings are provided for turbo generators with conventional DC rotating or static excitation system. These are of alloy steel forging shrunk fitted on the […]

Continue Reading

Generator Bearing & Rotor

Bearing:- The Turbo generators are provided with pressure lubricated self-aligning elliptical type bearing to ensure higher mechanical stability and reduced vibration in operations the bearing are either and shield mounted or pedestal type suitable temperature measurement device are mounted in the bearing to monitor bearing metal temp in operation.   Bearing insulation:- To prevent damage […]

Continue Reading

Generator Stator Bar’s and Winding

Stator Bar’s and Winding:- Stator bar design incorporates the use of thermosetting epoxy mica insulation conforming to class “F” The bars/coils during manufacture are provided with conductive coating wrapping tape for minimisation of corona discharge semiconductive varnish/tape is applied a uniform temp distribution in operation double-layer lap winding with half Rebel / multitier  type/diamond shaped […]

Continue Reading

Turbo Generators-Their sizes

Turbo Generators-Their sizes: In the table, I, II, III the various standard sizes of the Air/Hyderabad cooled Turbo generator (3000r.p.m) (Air cooled manufactured at BHEL Hyderabad are indicated at additional BHEL can undertake to manufacture tailor-made Turbo generator to suit specific customer requirement. Stator:- Stator frame is of welded steel single piece construction with radial […]

Continue Reading

ELECTRICAL MACHINES

ELECTRICAL MACHINES Introduction : BHEL has 13 manufacturing plants and a host of service divisions a vital link to this chain of BHEL manufacturing units is the unit at Ramachandrapuram   Hyderabad, manufactures turbo generator of rating up to 120mw for industrial application and for power generation to thermal power stations. These Turbo generators are supplied […]

Continue Reading

Stresses in compressor wheel

Stresses in compressor wheel: The forces exerted on the Gas turbine Rotor parts and resulting on that of compressor wheel are 1)        Air Force Airforce caused by the pressure difference between and down steam of the blades they can be steady or vibratory and can be minimized by sound aerodynamic design. 2)        Forces due to […]

Continue Reading

Specification & Rotor Wheel

Specification & Rotor Wheel: The compressor wheel is a part of a compressor rotor in gas turbine rotor each compressor wheel is machine separately and assembled with tie rods the compressor rotor is an axial flow type with 17 stages. Material Composition : The wheel is made of haste alloy (Ni, Cr, motored sheet) it […]

Continue Reading

MAJOR PARTS OF GAS TURBINE

MAJOR PARTS OF GAS TURBINE : Gas Turbine Parts : The main parts for the gas turbine are Base frame                Casings Diesel Engine            Turbine rotor Bearing housing       Bearings Works in drawer       Nozzles Stator Blades             Coolers Combustion system Molybdenum            –           1.4 Phosphorus   –           0.4 Gas Turbine rotor: The importance of Gas turbine this being known […]

Continue Reading

APPLICATION OF A GAS TURBINE

APPLICATION OF A GAS TURBINE POWER GENERATION : Highly capacity gas turbines are widely used in power generation and standby. The grid system: Power is produced and distributed continuously to large distances through a grid system. Standby generation: Power is produced for emergency uses in hospitals, Public buildings only for a local purpose. MECHANICAL DRIVER […]

Continue Reading

GAS TURBINE:

ABOUT GAS TURBINE:   The  Power generating turbo – machine decrease the head or energy laver of the working fluid (Like steam gas, hydro and wind) passing through them these machines are called turbines. They are coupled as primers to generators for generation of power and running of pumps compressors etc., A stage of turbomachine generally […]

Continue Reading

STEAM TURBINE AUXILIARY OIL

AUXILIARY OIL : Power oil at approximately 500kpa is supplied from pump through over speed  relay B up to speed drop setting value F. to mains stop valve oil cylinder C and up to control valve K the oil down steam of  F is pilot oil (100 – 400 kph) up to governor relay G […]

Continue Reading